Award Winning Electrical Service!

Milestone Is The Electrician Dallas & Ft. Worth Count On Everyday!

CALL NOW!

Your Local, Trusted & Friendly Electrician!

Dallas

Ft. Worth

214 267-2405

817 267-2405

  • SCHEDULE SERVICE TODAY!
  • FAQ

    We'll Fix It In A Flash!

    Circuit Overload

    Is it Possible?

    Are You Currently Running 4 Appliances Off of One Circuit?

    Well Unfortunately This Causes a Problem

    Electricity has enriched our lives. Despite the many benefits, electricity can also bring danger -- the most common being house fires. It is estimated that over 40,000 residential house fires are caused by electrical systems every year in the United States. This article discusses overloading electrical circuits.

    First, we must understand some basics about typical home electrical systems. The electrical service enters the house and connects to a main electrical panel. From the main electrical panel, wires run in different directions throughout the house to power lights, outlets, ceiling fans, air conditioners, and various other direct-wired electrical appliances. These wire-runs are called branch circuits.

    In home construction today, the typical branch circuit consists of three wires - the hot, neutral and ground wires. When a light or electrical appliance is turned on, electricity begins to flow in the hot and neutral wires of the branch circuit to which that light or electrical appliance is connected.

    When electricity flows through a wire, the wire heats up because of its resistance to the flow of electrical current. Both the size of the wire (resistance increases as the wire diameter gets smaller) and how many electrical devices on the circuit are drawing electricity (more devices increase the electrical current) affect the amount of heat generated in the wire. To keep the wire from getting too hot and starting a fire, the designer of the branch circuit wiring does two things:

    1. Attempts to size the wire large enough to handle the estimated electrical load on the circuit.
    2. Attempts to contain the amount of electrical load on the branch circuit by limiting the number of potential electrical appliances that can be running at the same time on that circuit (i.e. places only so many outlets on one branch circuit or puts larger pieces of electrical equipment on circuits dedicated to that equipment only).

    While the electrical codes help with the design assumptions, how the homeowner will use the outlets in the house is just a guess. The homeowner can plug in and run too many appliances on the same circuit at one time and overload the circuit.

    This is why electrical fuses and circuit breakers are used in the main electrical panel. Their function is to sense the overloading of circuits (and short circuits) and shut off power to that branch circuit before the wires get too hot and start fire.

    However, circuit breakers can malfunction and fail to trip. Homeowners can try to fix a "nuisance" fuse by placing a larger fuse in the electrical panel that allows more electrical current to flow in the branch circuit than what it was designed for. Homeowner can also use plug adapters and extension cords to plug in too many electrical appliances into one electrical outlet.

    What Can Homeowners Do?

    •If a fuse blows or circuit breaker trips frequently, have a qualified electrician determine what the problem is and fix it.
    •If the main electrical panel has circuit breakers, flip them off and back on once a year. This will help keep them working. It is also a good idea to have a qualified electrician out to your home or office to help you test the circuit breakers to make sure they are functioning properly.
    •If extension cords or plug adapters are being used to plug multiple appliances into the same outlet, have a qualified electrician intall more outlets ona new or different branch circuit(s).
    •It does not protect the more valuable in-home wiring such as your branch circuit wiring.The power strip and surge protector's circuit breaker only protect the devices which are plugged in to them. Using several plug strips on outlets on the same branch circuit may overload the circuit and cause a fire.
    •Never run appliance cords or extension cords underneath carpet. They are designed to be kept cool by movement of room air and around the cord.
    •If any outlet or switch wall plated feel hot to the touch, have a qualified electrician determine the problem and fix it right away, as it could lead to a potential fire safety hazard.
    •Circuits can only handle a specified total wattage of all electrical devices plugged into and running on a branch circuit at one time. Here is a guide from the National Electrical Safety Foundation (NESF) to follow: 15-amp branch circuit can carry 1500 watts
    20-amp branch circuit can carry 2000 watts

    Most home circuits are designed as 15-amp branch circuits. A hair dryer can draw 1400 watts, an iron 1000 watts, a portable heater 1200 watts, a vacuum cleaner 600 watts, deep fat fryer 1300 watts, and a portable fan 150 watts.

    There are no hard-and-fast rules as to how often a home electrical system should be inspected. Here are the recommendations from the NESF:

    If your last inspection was:

    •40 or more years ago, inspection is overdue.
    •10-40 years ago, inspection is advisable, especially if substantial electrical loads (high-wattage appliances, lights, and wall outlets or extension cords) have been added.
    •Less than 10 years ago, inspection may not be needed, unless problems are noticed.

    It may be difficult to determine when the last electrical inspection was made. Look on the inside of the door to the electrical panel. The electrician performing the last inspection may have written the date there.

    As a homeowner, be aware of your electrical system. Look and listen for problems. If you hear buzzing or crackling coming from outlets or light switches, don't ignore it. If an appliance or extension cord are hot to the touch, you have potential problems. Contact a qualified electrical professional to assess the problem and make the necessary repairs.

    1. "1997 Residential Fire Loss Estimates"
    2. "A Home Electrical Safety Check"; Plug Into Electrical Safety; The National Electrical Safety Foundation; 1300 N. 17th St., Suite 1847, Rosslyn, VA 22209, (703) 841-3211;

    State Farm ® believes the information contained in the Disaster Survival House is reliable and accurate. We cannot, however, guarantee the performance of all items demonstrated or described in all situations. Always consult an experienced and liicensed electrician to determine the best application of these ideas or products i n your home. Give us a call today - Milestone Electric - the trusted and highly referred Dallas Electricians.

    LET OUR FAMILY SERVE YOURS!

    Give Us A Call Today! Same Day Service Before 10AM For All Of DFW!

    Dallas County

    214-348-5100

    Tarrant County

    817-717-2055

    Collin County

    972-422-2999

    Rockwall County

    972-722-6988

    Denton County

    940-220-6759

    Ellis & Johnson County

    972-351-8185

    Hunt & Kaufman County

    903-274-4121

    Parker & Wise County

    817-458-4046

    SCHEDULE YOUR SERVICE

    Thanks For Contacting Us! We Will Respond In A Flash!